Share some IBM Certified System Administrator C9010-022 exam questions and answers below.
The AIX hosts node1 and node2 have Ethernet adapters, both named ent0, configured on the same network. Both are dedicated physical 1GB adapter ports in a Host Ethernet
Adapter. Based on this information and the output shown for each node, what is the most likely cause of intermittent failures and slow communication between these adapters?
A. The jumbo_frarnes setting is 'no' and should be set to 'yes'.
B. The Multi-Core Scaling mode is enabled. Multi-Core Scaling is interfering with communications because the processor is too busy.
C. The Shared Ethernet Adapter does not have enough bandwidth to accommodate the network traffic.
D. The media speed is set differently on the adapters than the endpoints on the switch.
Answer: D
A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network.He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?
A. Use the command 'Isdev -I ent0' on the host to determine the port VLAN ID.
B. Use the command 'Isattr-EI ent0' on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.
Answer: C
A physical LPAR has a failed Fibre Channel adapter, which was providing redundant SAN access. What is a prerequisite for using the Replace/Remove task of the PCI Hot Plug Manager?
A. Verify HMC RMC connectivity.
B. Unconfigure the adapter and child devices.
C. Make sure a spare adapter slot is available.
D. Provide additional SAN cabling.
Answer: B
Which command will display the path status of MultiPath I/O (MHO) device hdisk1?
A. Ispath-I hdisk1
B. Ispv-L hdisk1
C. chnlspath-I hdisk1
D. Isdev-Cp hdisk1
Answer: A
The/usr/sbin/clcmd command is not working as documented in an administrator's reference. How can the administrator determine if the command being run is at the same level as the command being referenced in the documentation?
A. Get the fileset name from Isipp-f, then check the level of the file set with lslpp-1.
B. Use Islpp-wto get the fileset name, then check the level of the file set with lslpp-1.
C. Use lslpp-1 to determine the fileset name and check the level.
D. Use Is-I to determine the last modified date of the command.
Answer: B
A DLPAR memory operation was attempted and failed. Given the following information, what is the likely caused
A. Source LPAR is using all of its allocated memory
B. Operation timed out
C. Destination LPAR maximum memory setting is too low.
D. HMC RMC daemons are not communicating properly to the source
E. Source LPAR minimum memory setting is too high.
F. Source LPAR maximum memory setting is too low.
Answer: C
Certpark IBM C9010-022 exam latest dumps is a proven software. With it you will get better theory than ever before. Before you decide to buy, you can try a free trial version, so that you will know the quality of the Certpark IBM C9010-022 exam latest dumps. It will be your best choice.Certpark is a convenient website to provide training resources for IT professionals to participate in the certification exam.
Certpark providing IBM C9010-022 exam latest dumps are very close to the content of the formal examination. Through our short-term special training You can quickly grasp IT professional knowledge, and then have a good preparation for your exam. We promise that we will do our best to help you pass the IBM certification C9010-022 exam.Nowadays in this talented society IT professionals are very popular, but the IT area are also very competitive.
No comments:
Post a Comment